Rat laminin (LN) elisa kit instructions for use - Huaqiang Electronic Network

Test - uppercase JPG - memory 146K
EL-C1600N100013-B
High-power led lamp beads 1W white light Sanan 30mil high power LED lamp beads imitation lumens
Kaixin micro test

examination range:

96T15μg/L -400μg/L

,

This kit is for research use only.

purpose of usage:

This kit is used to determine the level of laminin (LN) in rat serum, plasma and related liquid samples.

Experimental principle

:

The kit uses a double antibody sandwich assay to determine the level of laminin (LN) in the specimen. The microplate was coated with purified rat laminin (LN) antibody to prepare a solid phase antibody, and laminin (LN) was sequentially added to the microcapsule of the coated monoclonal antibody, followed by HRP-labeled laminin ( The LN) antibody binds to form an antibody-antigen-enzyme-labeled antibody complex, which is thoroughly washed and then added to the substrate TMB for color development. TMB is converted to blue under the catalysis of HRP enzyme and converted to the final yellow color by the action of an acid. The color depth is positively correlated with laminin (LN) in the sample. The absorbance (OD value) was measured at 450 nm using a microplate reader, and the concentration of rat laminin (LN) in the sample was calculated from a standard curve.

Specimen requirements

:

1.

The specimens should be extracted as soon as possible after collection, and the extraction should be carried out according to the relevant literature. The experiment should be carried out as soon as possible after extraction. If the test cannot be performed immediately, the specimen can be stored at -20 °C, but repeated freezing and thawing should be avoided.

2.

Samples containing NaN3 could not be detected because NaN3 inhibited horseradish peroxidase (HRP) activity.

Steps

:

1.

Dilution of Standards: This kit provides a standard of the original standard, which can be diluted in a small tube according to the following chart. 400μg/L No.5 standard 150μl original standard added 150μl standard dilution 200μg/L No.4 standard 150μl No.5 standard Add 150μl standard dilution 100μg/L No.3 standard 150μl No.4 standard Add 150μl standard dilution 50μg/L No. 2 standard 150μl No. 3 standard Add 150μl standard dilution 25μg/L No.1 standard 150μl No. 2 standard Add 150μl standard dilution

2.

Adding samples: blank holes (the blank control wells are not added with the sample and the enzyme standard reagent, the other steps are the same), the standard holes, and the sample holes to be tested. Accurately load 50 μl of the standard on the enzyme-labeled plate, add 40 μl of the sample dilution to the well to be tested, and then add 10 μl of the sample to be tested (the final dilution of the sample is 5 times). Add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, and shake gently to mix.

3.

Incubation: The plate was sealed with a sealing film and incubated at 37 ° C for 30 minutes.

4.

Dosing: Dilute 30 times concentrated washing solution with distilled water 30 times

5.

Washing: Carefully remove the sealing film, discard the liquid, dry it, fill each well with the washing solution, let stand for 30 seconds, then discard it, repeat 5 times, and pat dry.

6.

Add enzyme: 50 μl of enzyme labeling reagent was added to each well, except for blank wells.

7.

Incubation: The operation is the same as 3.

8.

Washing: The operation is the same as 5.

9.

Color development: Add 50 μl of the developer to each well, then add 50 μl of the developer B, gently shake and mix, and develop at 37 ° C for 10 minutes.

10.

Termination: 50 μl of stop solution was added to each well to terminate the reaction (in this case, the blue color turned yellow).

11.

Measurement: The absorbance (OD value) of each well was measured in sequence with a blank air conditioner of zero and a wavelength of 450 nm. The measurement should be carried out within 15 minutes after the addition of the stop solution. Summary of operation procedure: Calculate the concentration of the standard as the abscissa and the OD value as the ordinate. Draw a standard curve on the coordinate paper, and find the corresponding concentration from the standard curve according to the OD value of the sample; multiply by the dilution factor; or Calculate the linear regression equation of the standard curve by using the concentration of the standard and the OD value. Substituting the OD value of the sample into the equation, calculating the sample concentration, and multiplying by the dilution factor, is the actual concentration of the sample.

Precautions

:

1. The kit should be taken out from the refrigerated environment and allowed to equilibrate for 15-30 minutes at room temperature. If the enzyme label is unsealed after unsealing, the strip should be stored in a sealed bag. 2. Concentrated washing liquid may crystallize out. When diluted, it can be heated and dissolved in a water bath. The washing will not affect the result. 3. The sampler should be used for each step, and the accuracy should be corrected frequently to avoid test errors. It is best to control the loading time within 5 minutes. If the number of specimens is large, it is recommended to use a gun. 4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the substance to be tested in the specimen is too high (the OD value of the sample is larger than the OD value of the first hole of the standard well), please first dilute the sample dilution with a certain multiple (n times) and then measure it. When calculating, multiply the total dilution by the total dilution. Multiple (×n×5). 5. The sealing film is intended for single use only to avoid cross-contamination. 6. Please keep the substrate away from light. 7. Strictly follow the operation of the manual, the test results must be based on the reading of the microplate reader. All samples, washings and various wastes should be treated as infectious materials. 9. The different batch components of this reagent must not be mixed. Storage conditions and validity period 1. The kit is stored at: 2-8 °C. 2. Validity: 6 months

Purchase the company's elisa kit, enjoy zero-cost shipping, and improve after-sales. In addition, you can enjoy the authoritative enzyme-linked immunoassay service, skilled operators, and sophisticated laboratory equipment to ensure that each experimental data is true and reliable. The ELISA kits sold by the company are of quality assurance! Technical guidance is provided throughout the sale and after sale, and there are quality problems, which can be returned free of charge!

Right Angle DIP Centronic Connector

Right Angle DIP Centronic Connector.

Current Rating:5A
Dielectric Withstanding Voltage:1000V for one minute
Insulation Resistance:1000MΩ Min.(at 500V DC)
Contact Resistance:35mΩ Max.
Temperature:-55°C to +105°C

Right Angle DIP Centronic Connector

ShenZhen Antenk Electronics Co,Ltd , https://www.antenkconn.com

This entry was posted in on